
The AirTAC SE40 Standard Cylinder SE40X325 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 325mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X325 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies sensor placement along the three integrated grooves.
This 325 mm stroke unit features field-adjustable pneumatic cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw to soften hard impacts at high cycle rates. Because this specific SKU lacks the built-in -S magnet, it is wired for pure actuation rather than electronic position sensing.
| Model | Airtac SE40 Standard Cylinder SE40X325 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding and sealing arms on automated packaging lines, utilizing the 325 mm stroke to clear wide cardboard blanks during tooling changes.
Actuates a routing flap at transfer junctions, where the 628 N push force reliably redirects heavy boxed goods onto secondary chutes.
Positions linear carrier trays in diagnostic automation, benefiting from the flush tie-rod-free barrel that resists chemical washdowns.
If your application requires less force, stepping down to the 32 mm bore yields a 402 N push at 0.5 MPa, whereas upgrading to the 50 mm bore provides 982 N of push at 0.5 MPa. As a true ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 profile cylinders, sharing standard mounting hardware and a PT1/4 port. At 325 mm of stroke, the unsupported piston rod (Ø16 mm, M12x1.25 thread) is highly susceptible to bending under side loads; incorporating an external guide rail is critical to prevent premature rod-bearing wear. Note that this cylinder relies on live air pressure to move and cannot hold a load if air is lost.
Quick checklist
At 0.5 MPa, the SE40X325 generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum drive force is 128 kgf when operating at the 1.0 MPa pressure limit.
No, the SE40X325 is a double-acting cylinder that relies on continuous air pressure to move and hold position. If air is exhausted or a valve is centered, the piston will drift. The adjustable air cushions only decelerate the piston near the end of the stroke; they do not lock the rod. For position holding, a BSE rod lock variant or an external pilot-operated check valve is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.