verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X340S

The AirTAC SE40 Standard Cylinder SE40X340S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 340mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke340 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$82.78 $90.28Save 8% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X340S

The AirTAC SE40X340S is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a push force of 628 N at 0.5 MPa and a maximum push capacity of 128 kgf. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The integrated -S magnet enables direct position tracking using AirTAC CMSE reed or DMSE electronic sensors.

Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling loads across the 340 mm stroke. Operating at speeds of 30-800 mm/s, this unit uses a PT1/4 port and a 16 mm rod to reliably translate compressed air into linear motion.

Airtac SE40 Standard Cylinder SE40X340S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X340S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke340 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X340S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×340Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X340S Is Used

conveyor_belt

Pallet Diverting Gate

Actuates a routing flap on a 340 mm stroke to redirect flat-packed goods on a packaging conveyor, utilizing the 628 N push force to overcome guide friction.

packaging

Film Roll Tensioning

Maintains constant pressure on a shrink-wrap film feed assembly, using the built-in -S magnet and DMSE sensors to confirm material feed positioning.

warehouse

Carton Lid Flap Folding

Extends to fold corrugated carton flaps prior to tape sealing, relying on the field-adjustable cushioning to prevent denting the cardboard at end of stroke.

Is the Airtac SE40 Standard Cylinder SE40X340S the Right Cylinder?

Selecting the SE40X340S provides 628 N of push force at 0.5 MPa. If your application requires less thrust, stepping down to the 32 mm bore yields 402 N; conversely, scaling up to the 50 mm bore provides 982 N. Because this model features a 340 mm stroke, the 16 mm piston rod experiences increased bending moments under heavy side loads—utilizing an external guide rail is strongly recommended to prevent premature rod-bearing wear.

This cylinder serves as a direct replacement for any ISO 15552 profile cylinder with a 40 mm bore, 340 mm stroke, PT1/4 port, and basic mounting. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking mechanism. If the machine loses air pressure, the load will drift, requiring a BSE rod lock or external pilot check valve for secure holding.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X340S FAQ

The SE40X340S delivers a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.

Yes, the SE40X340S is dimensionally interchangeable with any standard ISO 15552 profile cylinder sharing a 40 mm bore, 340 mm stroke, and PT1/4 port. It uses standard ISO mounting accessories and is not a tie-rod type, ensuring a direct retrofit for profile body designs.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X340S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X340S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.