
The AirTAC SE40 Standard Cylinder SE40X370S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 370mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X370S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods entirely, yielding a highly compact, corrosion-resistant body that mounts flush against machine frames while leaving the integrated sensor rail exposed.
Because this specific unit includes the -S magnet code, it is fully primed for direct CMSE reed or DMSE electronic position sensing along the stroke. The pneumatic cushioning at both ends is field-adjustable via a set screw, allowing technicians to tune end-of-stroke deceleration and eliminate hard impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X370S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 370 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×370 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N thrust needed to actuate diverter gates on packaging lines, using its 370 mm stroke to fully clear standard conveyor widths.
Shifts tooling magazines in and out of machining centers, where the adjustable cushioning softens the impact of heavy carriages at end positions.
Raises and lowers the film carriage on stretch wrap machines, utilizing the built-in DMSE sensor magnet to trigger the rotation motor at precise heights.
With a 628 N push at 0.5 MPa, this 40 mm bore sits comfortably in the mid-range. If your payload is lighter, stepping down to the 32 mm bore yields 402 N push and saves valuable space; conversely, pushing heavier loads reliably requires stepping up to the 50 mm bore, which provides 982 N of thrust. This SE40X370S variant features a PT1/4 port, a 370 mm stroke, and a built-in magnet for CMSE / DMSE sensors.
Since the 370 mm stroke creates a long lever arm, side loads can induce severe bending moments on the M12x1.25 rod thread and front bearing. Implementing an external guide rail is strongly recommended to prevent premature wear. Furthermore, a standard SE cylinder relies on live air pressure to hold position; it will drift if air is lost, so integrate a BSE rod lock for fail-safe load holding.
Quick checklist
At 0.5 MPa, it provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push increases to 879 N. The maximum push is 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE40X370S is dimensionally interchangeable with any standard ISO 15552 profile cylinder. It uses the exact same mounting interface and PT1/4 port size, making it a direct retrofit for existing machinery without requiring bracket modifications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.