
The AirTAC SE40 Standard Cylinder SE40X400 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X400 is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard, delivering 628 N of push force and 528 N of pull force at 0.5 MPa. Its square extruded aluminum barrel completely eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing sensor grooves on three sides for flexible switch placement.
Because this specific SKU lacks the built-in magnet suffix (-S), it does not support AirTAC CMSE or DMSE position sensing out of the box. The cylinder relies on field-adjustable pneumatic cushioning at both stroke ends—tunable via a recessed screw to soften hard end-stop impacts at operating speeds up to 800 mm/s, which is a true velocity-deceleration mechanism rather than a fixed rubber bumper.
| Model | Airtac SE40 Standard Cylinder SE40X400 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Executes 400 mm routing strokes to shift containers between packaging lanes, utilizing the 628 N push force to overcome guide friction at high cycle rates.
Extends across the carton width to tuck heavy cardboard flaps, relying on the adjustable end cushions to decelerate the 16 mm rod before impact.
Acts as a 40 mm bore physical barrier to halt metal sheet advancement in a stamping press, retracting quickly at speeds up to 800 mm/s.
If your load requires less force, stepping down to a bore 32 cylinder reduces the 0.5 MPa push output to 402 N, whereas stepping up to a bore 50 unit increases it to 982 N. As a standard double-acting actuator, this SE40X400 will drift and cannot hold a load if air pressure is lost or the directional valve is centered; applications requiring true position holding without live pressure must pivot to the BSE rod-lock series or use an external pilot-operated check valve.
With a 400 mm stroke, the 16 mm rod and its M12x1.25 thread face a higher risk of side-load bending and bearing wear under unsupported loads. Specifying an external guide rail is strongly recommended to prevent rod deflection. For retrofits, this model is dimensionally interchangeable with any ISO 15552 cylinder of the same 40 mm bore and 400 mm stroke, sharing the PT1/4 port and standard mounting accessories without requiring custom bracketry.
Quick checklist
At 0.5 MPa, the SE40X400 delivers 628 N push and 528 N pull. At 0.7 MPa, the push force is 879 N, and it reaches a maximum push of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, PT1/4 port locations, and 400 mm stroke dimensions of competing profile cylinders for a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.