
The AirTAC SE40 Standard Cylinder SE40X400FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X400FTC is a double-acting single-rod ISO 15552 profile cylinder engineered for a 40 mm bore and 400 mm stroke. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, peaking at a maximum push of 128 kgf at 1.0 MPa. The extruded aluminum square barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This FTC-mounted unit features field-adjustable pneumatic cushioning at both ends to soften hard end stops over its 400 mm travel. Because this specific SKU lacks the -S magnet code, it is not wired for AirTAC CMSE or DMSE position sensing out of the box.
| Model | Airtac SE40 Standard Cylinder SE40X400FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N push needed to actuate diverter arms on high-speed packaging conveyors over a 400 mm span.
Exerts up to 128 kgf of max push to flatten and seat small metal brackets in light assembly presses.
Uses the FTC center-trunnion mount to pivot and index heavy pallets through 400 mm machining stations.
Stepping down to a 32 mm bore drops the 0.5 MPa push output to 402 N, while moving up to a 50 mm bore raises it to 982 N, letting you fine-tune actuation force to your actual load. With 400 mm of travel, the 16 mm rod and M12x1.25 thread face leverage forces that can bend the rod bearing under severe side loads; always pair this stroke length with an external guide rail to prevent premature seal wear. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct retrofit for standardized FTC mounting footprints without requiring custom brackets. Note that the adjustable end cushions only decelerate the piston near stroke end and do not hold a load if air pressure is lost.
Quick checklist
At 0.5 MPa, the 40 mm bore provides 628 N push and 528 N pull force, increasing to 879 N push at 0.7 MPa, with a maximum push of 128 kgf at 1.0 MPa. It uses a PT1/4 port and a 16 mm rod with an M12x1.25 thread.
Yes, the SE40X400FTC is dimensionally interchangeable per ISO 15552 standards, meaning it serves as a direct replacement for other ISO 15552 profile cylinders using the same FTC mounting interface.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.