
The AirTAC SE40 Standard Cylinder SE40X400SCA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X400SCA is a double-acting single-rod ISO 15552 profile cylinder engineered for robust linear motion. It features a 40 mm bore and a 400 mm stroke, generating 628 N of push force at 0.5 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific configuration includes a built-in magnet for CMSE or DMSE position sensing, alongside a CA single clevis mounting accessory for pivoting articulation. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X400SCA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Utilizes the 400 mm stroke and CA clevis to pivot packages between parallel conveyor lanes, relying on 628 N of push to overcome carton friction.
Applies steady 528 N retract force to maintain web tension on a packaging line, using the -S magnet to trigger DMSE sensors for roll replacement.
Advances blank metal sheets into a light stamping press, where the adjustable cushion absorbs kinetic energy at the 400 mm extension limit.
Selecting this 40 mm bore makes sense when an application requires 628 N of push at 0.5 MPa. If your load demands less force, stepping down to the 32 mm bore yields 402 N of push; conversely, scaling up to the 50 mm bore provides 982 N. Because this unit features a 400 mm stroke, the unsupported piston rod length increases bending moments under side loads—pairing it with an external guide rail prevents premature rod-bearing wear.
This model carries a CA single clevis mount and a built-in magnet for CMSE and DMSE sensors. It is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device, so loads will drift if air pressure is lost or the valve is centered.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf when operated at the 1.0 MPa pressure limit.
Yes, it conforms to ISO 15552 dimensional standards, making it a direct replacement for other ISO 15552 profile cylinders. The PT1/4 port and M12x1.25 rod thread match the standardized interface, and the built-in magnet works seamlessly with AirTAC CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.