
The AirTAC SE40 Standard Cylinder SE40X400SCB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X400SCB is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa and a maximum of 128 kgf at 1.0 MPa. Equipped with a built-in magnet, it seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
Its extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush, while the field-adjustable air cushioning at both ends allows you to tune end-stop deceleration for the 400 mm travel. The CB double clevis mounting accessory provides a pinned pivot connection ideal for articulating mechanisms.
| Model | Airtac SE40 Standard Cylinder SE40X400SCB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 628 N push force and 400 mm stroke to pivot a CB-mounted diverter arm, routing heavy cardboard cartons between sorting lanes at high speed.
Maintains dynamic tension on a stretch-wrap film feed via the double clevis pivot, absorbing web tension fluctuations while the 40 mm bore retracts with 528 N pull.
Actuates a heavy safety gate on a light-duty pneumatic press, utilizing the built-in magnet and DMSE sensor to confirm full open/close position to the PLC.
This 40 mm bore generates 628 N push at 0.5 MPa; if your mechanism requires less force, the 32 mm bore offers 402 N, whereas stepping up to the 50 mm bore yields 982 N. Remember that a standard SE cylinder relies on live air pressure to move and will drift if supply is lost—the air cushion only decelerates the piston near stroke end and does not act as a load lock. For position holding without pressure, consider a BSE rod lock variant.
With a 400 mm stroke, the 16 mm rod and M12x1.25 thread experience higher bending moments under side loads; an external guide rail is strongly recommended to prevent rod-bearing wear. This model is dimensionally interchangeable per ISO 15552, meaning it serves as a direct replacement for other ISO 15552 cylinders sharing the PT1/4 port and CB mounting footprint.
Quick checklist
At 0.5 MPa, the 40 mm bore provides 628 N of push force and 528 N of pull force. At 0.7 MPa, push increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No. The adjustable air cushion at both ends only decelerates the piston near the end of the stroke; it is not a mechanical brake. If air is lost, the piston will drift. For fail-safe load holding, use a BSE series rod lock cylinder or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.