
The AirTAC SE40 Standard Cylinder SE40X40H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 40mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X40H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature pneumatics. It generates 628 N of push force at 0.5 MPa over a 40 mm stroke, utilizing a PT1/4 port and a 16 mm hard-chrome rod. Because this SKU uses an FKM (Viton) seal, it operates reliably in ambient temperatures up to 150 C, making it ideal for hot molding or drying environments where standard TPU seals would fail.
The extruded aluminum barrel lacks external tie rods, yielding a smooth, flush profile that resists grime buildup and simplifies surface mounting. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration via a set screw, protecting payloads from hard impacts. This unit ships without a position-sensing magnet, so external stroke confirmation requires a mechanical stop or a separate sensor bracket.
| Model | Airtac SE40 Standard Cylinder SE40X40H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
With its 150 C FKM Viton seal, this cylinder reliably ejects plastic parts from hot injection molds, where radiant heat would quickly destroy standard TPU seals.
Provides 628 N of push at 0.5 MPa to knock stamped metal blanks off heated dies, using the adjustable air cushion to prevent end-cap damage during rapid strokes.
Actuates high-temperature laboratory drying oven doors, utilizing the smooth tie-rod-free extruded barrel that prevents debris accumulation in sterile environments.
Choosing this 40 mm bore depends on matching your load to its 628 N push at 0.5 MPa. If your application demands less force, stepping down to the 32 mm bore yields 402 N, while moving up to the 50 mm bore provides 982 N. Remember that a standard SE cylinder drifts when air pressure is lost or the valve centers, so it cannot hold a vertical load unpowered—consider a BSE rod-lock variant if fail-safe holding is mandatory. For ISO 15552 dimensional direct retrofits, verify your bore, 40 mm stroke, PT1/4 port, and mounting accessory footprint.
Quick checklist
The SE40X40H provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders for direct retrofits. The H suffix denotes a Viton (FKM) seal, extending the operating temperature range from -20 C up to 150 C for high-heat applications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.