
The AirTAC SE40 Standard Cylinder SE40X40S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 40mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X40S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact, high-cycle automation. Operating at 0.5 MPa, it generates 628 N of push force and 528 N of pull force, making it well-suited for mid-range industrial actuation. The extruded aluminum barrel omits external tie rods entirely, yielding a smooth, corrosion-resistant profile that mounts flush within tight machine envelopes.
Equipped with a built-in S-series magnet, this 40 mm bore unit directly supports AirTAC CMSE reed and DMSE electronic position sensing. The end caps integrate field-adjustable pneumatic cushioning at both ends, allowing technicians to fine-tune end-of-stroke deceleration and eliminate hard metal impacts during rapid 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X40S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of extend force at 0.5 MPa to secure aluminum castings against a machining datum, utilizing the 40 mm stroke for rapid jaw actuation.
Drives a mechanical folding arm at 30-800 mm/s to tuck corrugated box flaps prior to tape sealing, with DMSE sensors confirming the 40 mm stroke completion.
Actuates a lightweight routing gate on a PET bottle filling line, where the smooth tie-rod-less extruded barrel prevents debris accumulation.
When sizing this 40 mm bore actuator, evaluate your exact thrust margins: the smaller SE32X40S yields 402 N of push at 0.5 MPa, while the larger SE50X40S provides 982 N. If your mechanism must hold a vertical load during an air-loss event, note that a standard SE cylinder will drift; an AirTAC BSE rod-lock variant or external check valve is required for fail-safe positioning. For ISO 15552 dimensional retrofits, match the 40 mm bore, 40 mm stroke, PT1/4 port, and confirm the mounting accessory (such as an LB foot or FA front flange) and the required CMSE/DMSE sensors.
Quick checklist
At 0.5 MPa, the SE40X40S generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE40X40S is dimensionally interchangeable per ISO 15552 standards, sharing the exact 40 mm bore mounting footprint and PT1/4 port size. The built-in magnet also allows you to directly mount AirTAC CMSE reed or DMSE solid-state sensors without modifying the extruded barrel grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.