
The AirTAC SE40 Standard Cylinder SE40X40SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 40mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X40SN is a double-acting, single-rod ISO 15552 profile cylinder delivering 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with an NBR seal, this unit operates reliably within standard temperature ranges. The built-in magnet supports CMSE reed and DMSE electronic position sensing, while the field-adjustable air cushioning at both ends allows you to fine-tune end-of-stroke deceleration for fast-moving actuators.
| Model | Airtac SE40 Standard Cylinder SE40X40SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push and 40 mm stroke needed to fold and secure corrugated carton flaps at high cycling speeds on packaging lines.
Uses its compact profile and built-in magnet to quickly actuate routing gates on conveyor systems, reliably diverting lightweight packages.
Delivers consistent 528 N retract force to hold aluminum or plastic components firmly in place during light CNC machining and drilling.
If your application requires less force, stepping down to a 32 mm bore yields 402 N of push at 0.5 MPa, whereas scaling up to a 50 mm bore provides 982 N. This 40 mm bore operates at 30-800 mm/s and uses an M12x1.25 rod thread.
Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load if air pressure is lost. For position holding without live pressure, consider a BSE rod lock variant. Because this is a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 profile cylinders using the same mounting hardware.
Quick checklist
At 0.5 MPa, it provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa.
Yes. The SE40X40SN is dimensionally interchangeable per ISO 15552 standards, meaning it shares the same mounting interface, PT1/4 port, and 16 mm rod dimensions as other standard profile cylinders, allowing for a seamless direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.