
The AirTAC SE40 Standard Cylinder SE40X450SFA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 450mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X450SFA is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 40mm bore and 450mm stroke. It delivers 628 N of push force at 0.5 MPa and features an FA front flange mount for rigid axial load absorption. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in position magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushions at both ends allow technicians to tune end-cap deceleration, softening hard mechanical stops during high-speed 30-800 mm/s cycles.
| Model | Airtac SE40 Standard Cylinder SE40X450SFA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Gates PET bottles on a 450mm stroke using 628 N push at 0.5 MPa, relying on the FA front flange to withstand repeated lateral impacts during high-speed sortation.
Folds corrugated carton flaps with 528 N pull force, utilizing the -S magnet and DMSE electronic sensors to verify flap closure timing before the sealing head.
Adjusts yarn tensioner blocks on a 450mm travel path, tuning the field-adjustable air cushions to soften end-of-stroke impacts during 30-800 mm/s loom operations.
This 40mm bore generates 628 N push at 0.5 MPa. If your application requires less force, the neighboring 32mm bore provides 402 N; if you need higher thrust, the 50mm bore offers 982 N. Because this is a standard 450mm stroke, it falls within the 40mm bore's 1200mm maximum standard stroke limit. To replace an existing ISO 15552 cylinder, match the 40mm bore, 450mm stroke, PT1/4 port, FA front flange mounting, and the -S magnet requirement.
At 450mm of travel, the 16mm rod and front flange bearing face increased bending moments under heavy side loads. For long unsupported strokes, integrating an external guide rail prevents premature seal wear and rod deflection. Note that a plain SE cylinder drifts when air is exhausted; use a BSE rod lock for position holding.
Quick checklist
At 0.5 MPa, this 40mm bore cylinder provides 628 N push and 528 N pull force. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE40X450SFA is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. Ensure your existing setup matches the 40mm bore, 450mm stroke, PT1/4 port, and FA front flange mounting interface for a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.