
The AirTAC SE40 Standard Cylinder SE40X470S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 470mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X470S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force and 528 N of pull force at 0.5 MPa. Driven by a 16 mm hard-chrome piston rod with an M12x1.25 thread, it utilizes a PT1/4 port to efficiently manage pneumatic flow within a 30-800 mm/s speed range.
This unit features a square extruded aluminum barrel completely free of external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Equipped with a built-in magnet (-S), it seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection, while the field-adjustable air cushioning at both ends allows technicians to fine-tune deceleration and eliminate hard end-stop impacts.
| Model | Airtac SE40 Standard Cylinder SE40X470S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 470 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×470 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives routing gates on package sortation lines, utilizing the 470 mm stroke to fully open diverts while the 628 N push force reliably overcomes belt friction.
Extends mechanical arms to fold major and minor corrugated box flaps prior to sealing, leveraging the 16 mm rod and adjustable cushions to prevent tearing cardboard at high speeds.
Deploys stopper mechanisms in pallet infeed conveyors, where the built-in magnet triggers DMSE sensors to confirm the stopper is raised before payload transfer.
With a 470 mm stroke and 628 N push at 0.5 MPa, this 40 mm bore cylinder fits mid-range actuation tasks perfectly. If your assembly requires less force, stepping down to the 32 mm bore yields 402 N of push, whereas upgrading to the 50 mm bore provides 982 N for heavier payloads. Because this model features a 470 mm stroke, the 16 mm rod is highly susceptible to bending under lateral loads; always pair it with an external guide rail to prevent rod-bearing damage.
As a dimensionally interchangeable ISO 15552 component, the SE40X470S serves as a direct replacement for other standard profile cylinders, sharing identical mounting footprints and PT1/4 port locations. Note that the adjustable air cushion only decelerates the piston near the stroke ends; it does not hold loads. If pressure is lost, the rod drifts, requiring a BSE rod lock for true position holding.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force reaches 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. It operates at pressures from 0.15-1.0 MPa with a speed range of 30-800 mm/s.
Yes. The SE40X470S is dimensionally interchangeable per ISO 15552 standards, meaning it shares identical mounting dimensions, 470 mm stroke, and PT1/4 port locations with other standard profile cylinders, allowing for a seamless direct retrofit without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.