
The AirTAC SE40 Standard Cylinder SE40X475 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 475mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X475 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa over a 475 mm stroke. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized mounting interfaces for immediate interchangeability.
This specific SKU is configured without a position-sensing magnet, relying instead on its field-adjustable pneumatic cushioning at both ends to decelerate the 16 mm piston rod smoothly. The cushion needles allow technicians to dial in end-of-stroke speeds precisely, preventing hard mechanical impacts without relying on fixed rubber bumpers.
| Model | Airtac SE40 Standard Cylinder SE40X475 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 475 mm stroke and 628 N push force to divert medium-weight packaging cartons across a transfer belt without overwhelming the mechanism.
Extends automated laboratory sample drawers fully, utilizing the adjustable cushions to prevent sudden stops that could spill sensitive liquids.
Adjusts the tensioning arm on a wrapping machine, where the tie-rod-free profile body allows flush mounting inside narrow guarding.
When sizing this 40 mm bore, you can step down to a 32 mm bore for 402 N of push at 0.5 MPa, or step up to a 50 mm bore for 982 N. Because this model features a 475 mm stroke, the unsupported rod length increases susceptibility to bending under lateral loads; always pair it with an external guide rail to prevent rod-bearing wear. As a standard ISO 15552 cylinder, it serves as a direct replacement for any equivalent 40 mm bore profile cylinder with a PT1/4 port and 475 mm stroke. Note that a plain SE cylinder will drift if air pressure is lost; for position holding, consider the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
This specific SE40X475 SKU is built without a magnet, so it cannot host AirTAC CMSE reed or DMSE electronic sensors. If your application requires position detection, you must select the SE40X475-S variant with the built-in magnet.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.