
The AirTAC SE40 Standard Cylinder SE40X475S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 475mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X475S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics from washdown debris.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to dial in end-of-stroke deceleration, softening hard impacts during high-speed 475 mm traverse cycles.
| Model | Airtac SE40 Standard Cylinder SE40X475S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates routing gates on high-speed packaging lines, using the 475 mm stroke to clear wider product lanes while the 628 N push force reliably overcomes carton friction.
Advances raw bar stock into collet chucks, where the 40 mm bore provides steady push force and the integrated magnet confirms material insertion for the machine controller.
Stages corrugated cardboard sheets at the end of palletizing machines, requiring the long stroke and no-tie-rod profile to fit within tight conveyor side-rail clearances.
When sizing this 40 mm bore unit, consider stepping down to a 32 mm cylinder (402 N push at 0.5 MPa) for lighter loads, or up to a 50 mm bore (982 N push at 0.5 MPa) if your payload demands higher thrust. Because this model features a 475 mm stroke, the extended rod is susceptible to bending under lateral loads; always support the tooling with an external linear guide to prevent premature rod-bearing wear.
As a dimensionally interchangeable ISO 15552 component, the SE40X475S serves as a direct replacement for competing standard-profile cylinders, matching the 40 mm bore, 475 mm stroke, PT1/4 port, and standardized mounting footprint. Note that the adjustable cushion only decelerates the piston near stroke end and does not hold the load if air pressure is lost.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum drive force is 128 kgf at 1.0 MPa.
No. The SE40X475S is a standard double-acting cylinder; the adjustable air cushions only decelerate the piston near the stroke ends and do not act as a mechanical brake. If you need to hold a load without live air pressure, consider the AirTAC BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.