
The AirTAC SE40 Standard Cylinder SE40X480S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 480mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X480S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force and 528 N of pull force at 0.5 MPa. Driven by a 16 mm hard-chrome rod and a PT1/4 port, it operates efficiently at speeds between 30 and 800 mm/s. The 480 mm stroke provides ample travel for mid-range positioning tasks.
Its square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting and sensor placement. Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position switches via the integrated sensor grooves on three sides of the body.
| Model | Airtac SE40 Standard Cylinder SE40X480S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 480 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×480 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 480 mm stroke and 628 N push to extend and redirect heavy pallets along a transfer line without stalling.
Leverages the no-tie-rod profile and CMSE magnet sensors to automate wide machine-guard doors cleanly within a compact footprint.
Applies the 528 N pull force to fold and hold corrugated cardboard flaps during high-speed adhesive application.
This 40 mm bore generates 628 N push at 0.5 MPa. If your application demands less force, stepping down to the 32 mm bore yields 402 N push; conversely, scaling up to the 50 mm bore provides 982 N push. Because this 480 mm stroke creates a long lever arm on the 16 mm rod, side-loading can induce severe rod-bearing bending—an external guide is strongly recommended to prevent premature wear.
For ISO 15552 dimensional direct retrofits, match the 40 mm bore, 480 mm stroke, PT1/4 port, and your specific mounting accessory. Remember that the adjustable air cushions at both ends only decelerate the piston near stroke end; they do not lock or hold a load. If unpowered position holding is required, specify a BSE rod-lock cylinder or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder outputs 628 N push and 528 N pull. At 0.7 MPa, the push force reaches 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The 480 mm stroke falls within the 1200 mm maximum standard stroke limit for this bore size.
Yes, the SE40X480S is dimensionally interchangeable per ISO 15552 mounting dimensions, allowing it to drop into existing setups. The built-in magnet is specifically designed to interface with AirTAC CMSE reed and DMSE electronic sensors housed in the standard barrel grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.