
The AirTAC SE40 Standard Cylinder SE40X490S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 490mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X490S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a corrosion-resistant body that mounts flush against machine frames without snagging on adjacent wiring.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing. Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration, softening hard impacts when cycling 490 mm at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X490S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 490 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×490 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Driving the vacuum pickup arm on a carton erector, where the 490 mm stroke unfolds corrugated blanks and the 628 N push force reliably squares the box flaps for sealing.
Operating a pneumatic diverter gate on a packaging conveyor, using the 40 mm bore's 528 N pull force to retract the blade and the -S magnet to trigger DMSE electronic sensors for timing.
Moving sample racks between analytical stations in diagnostic automation, where the compact tie-rod-free profile prevents debris accumulation and the adjustable cushion ensures gentle stops.
Stepping up to the 50 mm bore yields 982 N of push at 0.5 MPa for heavier payloads, while dropping to the 32 mm bore provides 402 N when space is tight. Because this is a 490 mm stroke, the 16 mm rod and M12x1.25 thread face increased bending moments under side loads; integrating an external guide rail prevents rod-bearing wear. As a standard ISO 15552 profile cylinder, it serves as a dimensionally interchangeable direct replacement for any ISO 15552 cylinder, sharing standard mounting hardware and PT1/4 ports. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold loads; if position holding is required when air pressure is lost, specify a BSE rod lock variant.
Quick checklist
The SE40X490S provides 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N, and it reaches a maximum push capacity of 128 kgf at 1.0 MPa.
Yes, the SE40X490S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint and PT1/4 port locations of other ISO 15552 profile cylinders for seamless retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.