
The AirTAC SE40 Standard Cylinder SE40X50FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X50FTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 40 mm bore and a 50 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a clean, corrosion-resistant profile that mounts flush against machine frames.
This specific SKU is configured with an FTC mounting interface and a standard PT1/4 port. Because it lacks the -S magnet option, it does not support AirTAC CMSE or DMSE position sensors out of the box. The integrated field-adjustable air cushions at both ends allow technicians to dial in end-of-stroke deceleration, preventing harsh impacts during cycling speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X50FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of extend force at 0.5 MPa to secure aluminum housings against a CNC machining center's subplate, using the short 50 mm stroke for rapid clamp and release cycles.
Uses the FTC mount to pivot a mechanical arm, folding corrugated cardboard flaps at high throughput speeds while relying on the adjustable cushion to soften end stops.
Actuates a routing gate on a packaging conveyor, leveraging the clean profile barrel to resist washdown splashes and the 528 N retract force to pull the gate clear.
When sizing this 40 mm bore actuator, evaluate your force margins against neighboring ISO 15552 options. Stepping down to a 32 mm bore reduces the 0.5 MPa push to 402 N, while moving up to a 50 mm bore increases it to 982 N. If your fixture must hold position without live air pressure, note that this standard SE cylinder will drift; an AirTAC BSE rod lock variant is required for secure load holding.
For retrofitting, match the 40 mm bore, 50 mm stroke, PT1/4 port, and FTC mounting accessory. The standardized ISO 15552 mounting dimensions ensure direct compatibility with other ISO 15552 cylinders. Since the stroke is under 300 mm, side-load bending on the 16 mm rod is minimal, though external guides are still recommended for heavy off-center loads.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa.
Yes, the SE40X50FTC is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing FTC mounting hardware designed for other ISO 15552 profile cylinders. Ensure your port matches the PT1/4 thread form.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.