
The AirTAC SE40 Standard Cylinder SE40X50S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X50S is a double-acting single-rod ISO 15552 profile cylinder engineered with a 40mm bore and 50mm stroke. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, making it highly suitable for medium-duty industrial tasks. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machinery frames.
This specific configuration includes a built-in magnet (-S) designed to interface seamlessly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Furthermore, the cylinder incorporates field-adjustable pneumatic cushioning at both ends, allowing technicians to tune the end-of-stroke deceleration via a set screw to eliminate hard mechanical impacts during high-speed operations.
| Model | Airtac SE40 Standard Cylinder SE40X50S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding jaws on automated packaging lines, utilizing the 628 N push force and 50mm stroke to form corrugated cartons rapidly.
Actuates a routing gate to sort products on a conveyor belt, relying on the CMSE/DMSE magnet feedback for precise timing.
Applies 628 N of force to stake bearings or pins into housings, benefiting from the tunable air cushion to prevent workpiece damage.
When sizing this actuator, consider stepping down to a 32mm bore (402 N push at 0.5 MPa) for lighter loads, or up to a 50mm bore (982 N push at 0.5 MPa) if your application requires greater thrust. As a standard ISO 15552 profile cylinder, the SE40X50S serves as a direct replacement for any ISO 15552 cylinder, sharing standardized mounting dimensions and utilizing a PT1/4 port. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If your system loses air pressure, the rod will drift unless a BSE rod lock or external pilot-operated check valve is installed.
Quick checklist
The SE40X50S delivers a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE40X50S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, retaining your existing mounting hardware and PT1/4 pneumatic connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.