verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X570S

The AirTAC SE40 Standard Cylinder SE40X570S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 570mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke570 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$109.56 $117.06Save 6% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X570S

The AirTAC SE40X570S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 40 mm bore and 570 mm stroke. It delivers 628 N of push force at 0.5 MPa, utilizing a hard-chrome plated Ø16 mm rod with an M12x1.25 thread. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining the standardized ISO 15552 footprint.

Because this unit includes the -S magnet code, it is fully primed for CMSE reed and DMSE electronic position sensing. The integrated pneumatic cushioning at both ends is field-adjustable via a set screw, allowing you to fine-tune end-of-stroke deceleration for varying loads. This true cushion actively slows the piston rather than relying on a fixed rubber bumper.

Airtac SE40 Standard Cylinder SE40X570S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X570S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke570 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X570S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×570Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X570S Is Used

conveyor_belt

Bottling Line Diverter

Pushes 570 mm to route plastic bottles between packaging lanes using 628 N of extend force at 0.5 MPa.

precision_manufacturing

CNC Lathe Door Actuator

Utilizes the -S magnet and DMSE sensors to confirm full door closure before machining cycles begin.

warehouse

Palletizing Stop Gate

Deploys the 570 mm stroke to halt incoming wooden pallets, relying on adjustable cushions to soften the hard stop.

Is the Airtac SE40 Standard Cylinder SE40X570S the Right Cylinder?

Stepping up to the 50 mm bore yields 982 N of push at 0.5 MPa, whereas stepping down to the 32 mm bore provides 402 N. If your application requires holding a load without live air pressure, note that a standard SE cylinder will drift when air is exhausted; you should integrate an external pilot-operated check valve or transition to the BSE rod-lock variant. For a 570 mm stroke, the unsupported piston rod is highly susceptible to side-load bending; always use an external guide to prevent rod-bearing damage. When retrofitting, match the 40 mm bore, 570 mm stroke, PT1/4 port, and your specific mounting accessory for a seamless ISO 15552 direct replacement.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X570S FAQ

At 0.5 MPa, the SE40X570S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.

Yes. The SE40X570S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders by matching the 40 mm bore, 570 mm stroke, and PT1/4 port size.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X570S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X570S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.