
The AirTAC SE40 Standard Cylinder SE40X577S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 577mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X577S is a double-acting, single-rod ISO 15552 profile cylinder featuring a 40mm bore and a non-standard 577mm stroke. It delivers a push force of 628 N at 0.5 MPa and an extend thrust of 879 N at 0.7 MPa. The extruded aluminum barrel lacks external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies bracket installation on tight machine frames.
Equipped with a built-in magnet, this unit supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke verification. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, softening impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X577S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 577 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×577 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on intermittent-motion carton erectors, utilizing the 577mm stroke to clear wide packaging web paths before the 628 N push force seals the bottom flaps.
Actuates a diverting gate on a 40mm roller conveyor, relying on the 879 N extend thrust at 0.7 MPa to overcome friction and pivot the guide arms smoothly for heavy SKU routing.
Moves a multi-port sample dispensing head across a testing bench, using the built-in magnet with DMSE electronic sensors to confirm full extension at the 577mm travel limit.
This 40mm bore generates 628 N of push at 0.5 MPa. If your load requires less force, the 32mm variant offers 402 N; if you need heavier thrust, stepping up to the 50mm bore provides 982 N. Because the 577mm stroke exceeds the 1200mm maximum standard range, this is a made-to-order configuration.
A standard SE cylinder drifts when air is removed or a valve centers, so it cannot hold a load without live pressure. For secure position holding, consider the BSE rod lock series. Since the stroke exceeds 300mm, the 16mm rod and bearing are subject to bending under side loads; always use an external guide to prevent premature seal wear. The PT1/4 port and M12x1.25 rod thread ensure standardized ISO 15552 mounting interchangeability.
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa. The operating speed ranges from 30 to 800 mm/s.
Yes, the SE40X577S is dimensionally interchangeable per ISO 15552 mounting interface standards. It uses a PT1/4 port and M12x1.25 rod thread, sharing standardized mounting hardware with other ISO 15552 profile cylinders without requiring custom brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.