
The AirTAC SE40 Standard Cylinder SE40X5S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 5mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X5S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact actuation. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, making it a robust choice for short-travel automation. The extruded aluminum barrel omits external tie rods entirely, yielding a clean profile that resists corrosion and mounts flush against machine frames.
Fitted with a built-in magnet, this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The integrated air cushions at both ends are field-adjustable via a set screw, allowing technicians to tune deceleration and soften hard mechanical stops during rapid 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X5S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 628 N push force at 5 mm to secure delicate printed circuit boards within CNC routing fixtures without flexing the substrate.
Rapidly closes packaging film sealing bars using the 30-800 mm/s speed range and DMSE electronic sensors for precise timing.
Acts as a hard mechanical stop in feed lines, extending the 16 mm rod just 5 mm to register sheet metal blanks for bending presses.
Selecting the SE40X5S is ideal when a 628 N push stroke at 0.5 MPa fits your load requirement within a tight 5 mm travel. If your application demands less force, stepping down to the 32 mm bore yields 402 N of push, while stepping up to the 50 mm bore provides 982 N for heavier clamping. Because this is a standard 40 mm bore with a PT1/4 port and M12x1.25 rod thread, it serves as a direct dimensional direct replacement for any ISO 15552 cylinder footprint.
As a double-acting cylinder, it relies on continuous air pressure to maintain position; if air is lost or the valve is centered, the piston will drift. For applications requiring true load holding without live pressure, pair this cylinder with an external pilot-operated check valve or consider the BSE rod-lock variant. The 5 mm stroke keeps the rod fully supported by the bearing, minimizing side-load bending.
Quick checklist
At 0.5 MPa, the SE40X5S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N, with an absolute maximum push of 128 kgf at 1.0 MPa. It features a 40 mm bore, 16 mm rod, PT1/4 port, and operates at speeds of 30-800 mm/s.
No, the SE40X5S is a double-acting cylinder and its adjustable air cushions only decelerate the piston near the stroke ends; they do not lock or hold the load. If power or air is lost, the rod will drift. For fail-safe load holding, an external rod lock or the AirTAC BSE series is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.