
The AirTAC SE40 Standard Cylinder SE40X600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 600mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X600S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 600 mm stroke. It features a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush on standardized tooling plates. At 0.5 MPa, this 40 mm bore unit generates 628 N of push force and 528 N of pull force, scaling to a maximum 128 kgf at 1.0 MPa.
Because this unit carries the -S option, it includes a built-in magnet for seamless triggering of CMSE reed and DMSE electronic position sensors along the three integrated side grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-velocity 600 mm traversals.
| Model | Airtac SE40 Standard Cylinder SE40X600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 600 mm stroke to push heavy pallets onto a secondary belt, leveraging the 628 N push force to overcome friction without stalling.
Extends across the 600 mm span to fold large carton flaps, relying on the -S magnet and DMSE sensors to confirm flap closure timing.
Drives a 600 mm linear displacement to rotate a multi-position sample carousel, utilizing the adjustable cushion to halt the 40 mm bore smoothly at high speeds.
If your assembly requires less push force, stepping down to the 32 mm bore yields 402 N at 0.5 MPa, whereas moving up to the 50 mm bore provides 982 N for heavier payloads. To execute a true ISO 15552 replacement, verify the 40 mm bore, 600 mm stroke, PT1/4 port, and your specific mounting accessory. Note that a plain SE cylinder does not hold its position or load when air is lost or the valve centers; the piston will drift, so use a BSE rod lock for fail-safe holding.
With a 600 mm stroke, the 16 mm rod and M12x1.25 thread face significant bending moments under side loads. For long unsupported strokes like this, integrating an external linear guide is strongly recommended to prevent rod-bearing wear and premature seal failure.
Quick checklist
The 40 mm bore provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum of 128 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, the SE40X600S is dimensionally interchangeable per ISO 15552. Its profile barrel shares the exact mounting footprint and PT1/4 port locations of other standard ISO 15552 cylinders, ensuring a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.