
The AirTAC SE40 Standard Cylinder SE40X60S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 60mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X60S is a double-acting single-rod profile cylinder operating at 628 N push and 528 N pull at 0.5 MPa. Built to the ISO 15552 standard, its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine envelopes.
Because this unit includes the -S magnet code, it is wired for AirTAC CMSE reed and DMSE electronic position sensing. The end caps house field-adjustable pneumatic cushioning, letting technicians dial in the exact deceleration needed to soften hard end stops during rapid 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X60S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push at 0.5 MPa required to fold corrugated cardboard flaps on high-speed packaging lines without crushing the box structure.
Uses the built-in magnet with DMSE sensors to confirm the 60 mm stroke position, rapidly routing small parcels between adjacent conveyor belts at speed.
Secures delicate printed circuit boards during routing operations, utilizing the adjustable end cushions to prevent harsh impact at the 60 mm stroke limit.
If 628 N of push at 0.5 MPa is too much force, step down to the 32 mm bore (402 N push); if you need more thrust, step up to the 50 mm bore (982 N push). As a standard ISO 15552 cylinder, the SE40X60S is dimensionally interchangeable with other ISO 15552 profile cylinders, accepting standard FA front flange or LB foot mounting hardware and a PT1/4 port.
Note that the adjustable air cushion only decelerates the piston near stroke end and does not lock the rod. If your process loses air pressure, the cylinder will drift and cannot hold a vertical load—specify a BSE rod lock or external pilot check valve for fail-safe holding.
Quick checklist
At 0.5 MPa, the SE40X60S provides 628 N push and 528 N pull force. At 0.7 MPa, the push increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa, and it operates at speeds between 30-800 mm/s.
Yes, the SE40X60S is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other ISO 15552 profile cylinders using your existing mounting hardware and PT1/4 ports.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.