verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X625S

The AirTAC SE40 Standard Cylinder SE40X625S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 625mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke625 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$120.73 $128.23Save 5% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X625S

The AirTAC SE40X625S is a double-acting single-rod ISO 15552 profile cylinder with a 40 mm bore and a 625 mm stroke. It generates 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa, utilizing a PT1/4 port and a 16 mm hard-chrome rod. Because the stroke exceeds the 1200 mm standard maximum, this unit is produced as a non-standard made-to-order configuration.

The extruded aluminum barrel omits external tie rods, yielding a smooth, compact body that is highly resistant to corrosion and easy to mount flush against machine frames. Equipped with a built-in magnet (S option), the cylinder readily interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-travel detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration for the specific load and speed.

Airtac SE40 Standard Cylinder SE40X625S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X625S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke625 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X625S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×625Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X625S Is Used

conveyor_belt

Carton Diverting Arms

Provides 628 N of push at 0.5 MPa to reliably pivot diverter arms on high-speed packaging conveyor lines, utilizing the 625 mm stroke to reach across the belt.

straighten

Pallet Stop Gates

Deploys the full 625 mm travel to halt heavy pallets at machining centers, using the adjustable end cushions to soften the impact of the 16 mm rod extension.

science

Textile Tenter Frames

Extends and retracts to control fabric tensioning webs, leveraging the smooth tie-rod-less profile body for flush mounting in washdown environments.

Is the Airtac SE40 Standard Cylinder SE40X625S the Right Cylinder?

At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force. If your application requires less force, stepping down to the 32 mm bore yields 402 N, while moving up to the 50 mm bore provides 982 N. Because this is a 625 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads; always use an external guide to prevent premature rod-bearing wear. Remember that a standard SE cylinder will drift if air pressure is lost or the valve is centered—use a BSE rod lock variant if the load must be held safely without live pressure. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement sharing standard mounting hardware and footprint.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X625S FAQ

The SE40X625S delivers 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.

Yes, the SE40X625S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface and footprint as other ISO 15552 cylinders for easy retrofitting. The included -S magnet also allows seamless integration with AirTAC CMSE and DMSE position sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X625S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X625S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.