
The AirTAC SE40 Standard Cylinder SE40X690S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 690mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X690S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 690 mm stroke, yielding 628 N of push force and 528 N of pull force at 0.5 MPa. Because this 690 mm stroke exceeds the standard 1200 mm maximum for this bore, it is manufactured as a non-standard made-to-order unit to precisely fit your long-travel machinery requirements.
Its extruded aluminum barrel omits external tie rods entirely, presenting a clean, flush-mounting surface that resists corrosion and simplifies bracket installation. The integrated -S magnet enables direct mounting of CMSE reed and DMSE electronic sensors along the three-sided sensor grooves, while field-adjustable air cushions at both ends allow you to precisely tune end-of-stroke deceleration for heavy moving loads.
| Model | Airtac SE40 Standard Cylinder SE40X690S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 690 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×690 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Ideal for pushing heavy pallets across a 690 mm transfer gap, utilizing the 628 N push force to overcome friction while the adjustable cushion softens the stopping impact at full extension.
Provides the long linear travel and reliable 528 N retract force needed to hold and fold extended corrugated carton flaps on continuous packaging lines without buckling.
Suitable for loading heavy fabric beams into dyeing machines, where the integrated -S magnet triggers DMSE electronic sensors to confirm beam placement across the 690 mm span.
When sizing this cylinder, consider stepping down to a 32 mm bore if your application requires less energy, offering 402 N of push at 0.5 MPa, or stepping up to a 50 mm bore for heavier loads, which provides 982 N of push at 0.5 MPa. Because this is a plain double-acting cylinder, it cannot hold a load vertically if air pressure is lost or the valve is centered; a BSE rod lock variant or external pilot-operated check valve is required for secure positioning.
At 690 mm of stroke, the 16 mm rod and internal bearing face significant bending moments under side loads; an external guide rail is strongly recommended to prevent premature seal wear and piston scoring. As a true ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to drop it into existing foot or flange mounting hardware seamlessly.
Quick checklist
The SE40X690S generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 879 N. The maximum operating pressure is 1.0 MPa, where it achieves a maximum push of 128 kgf.
Yes, the SE40X690S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, PT1/4 port size, and 16 mm rod thread for direct replacement without modifying your existing machinery.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.