
The AirTAC SE40 Standard Cylinder SE40X700S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 700mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X700S is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous pneumatic duty. At 40 mm bore and 700 mm stroke, it generates 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant profile that mounts flush against machine frames while protecting against mechanical wear.
This specific unit includes a built-in magnet (-S) for non-contact position sensing, interfacing directly with AirTAC CMSE reed and DMSE electronic switches. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.
| Model | Airtac SE40 Standard Cylinder SE40X700S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Gates and diverts continuous PET bottle traffic on high-speed packaging lines, utilizing the 700 mm stroke and 628 N push to cleanly shift product mass into secondary processing lanes.
Pushes raw steel blanks into a mechanical stamping press, where the 879 N force at 0.7 MPa overcomes strip friction and the adjustable cushion absorbs end-of-stroke momentum.
Acts as a physical halt for outbound corrugated cartons accumulating on gravity roller conveyors, using the integrated magnet to trigger DMSE sensors for precise stacking logic.
When sizing this 40 mm bore actuator, consider stepping down to a 32 mm bore (402 N push at 0.5 MPa) for lighter loads, or up to a 50 mm bore (982 N push at 0.5 MPa) if your payload demands greater thrust. Because the 700 mm stroke is substantial, the 16 mm rod and internal bearing face elevated bending moments under lateral loads; always incorporate an external guide rail to prevent side-load damage. As a true ISO 15552 cylinder, it offers direct dimensional interchangeability with other standardized profile cylinders, sharing identical mounting footprints and PT1/4 port locations for seamless retrofits. Note that this actuator relies on live air pressure to move; if your process requires static load holding during pressure loss, explore the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
The SE40X700S provides a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N. The absolute maximum push capacity is 128 kgf when operated at the maximum rated pressure of 1.0 MPa.
Yes, the SE40X700S is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders, matching the 40 mm bore, 700 mm stroke, PT1/4 port, and standard mounting accessories without redesigning your machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.