
The AirTAC SE40 Standard Cylinder SE40X700SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 700mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X700SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 700 mm stroke. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 16 mm rod with an M12x1.25 thread. Because it features an extruded aluminum barrel without external tie rods, the body is highly compact, corrosion-resistant, and easy to mount flush against machine frames.
This specific configuration includes a built-in magnet for CMSE and DMSE position sensing, along with a high-temperature FKM seal that extends the operating range up to 150 C. The field-adjustable air cushion at both ends allows you to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving loads at speed.
| Model | Airtac SE40 Standard Cylinder SE40X700SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles the long-stroke film carriage travel on continuous motion wrappers, where the FKM seal survives proximity to heat tunnels and the 628 N push force maintains steady carriage tension.
Transfers heavy cardboard pallets onto secondary processing lines, utilizing the full 700 mm stroke to index products without requiring a multi-stage cylinder.
Actuates the large doors of high-temperature drying ovens, where the FKM Viton seal reliably endures 150 C ambient heat and the adjustable cushion prevents door slamming.
Stepping down to the SE32 bore reduces the 0.5 MPa push force to 402 N, while stepping up to the SE50 bore increases it to 982 N, allowing you to scale power precisely to your payload. Remember that a plain SE cylinder does not hold its load when air is exhausted or a valve is centered; the piston will drift. If your process requires mid-stroke holding without live pressure, consider the BSE rod lock variant. As a dimensionally interchangeable ISO 15552 component, this 40 mm bore, 700 mm stroke, PT1/4 port cylinder serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting accessories. Because the 700 mm stroke is substantial, the unsupported rod bearing faces bending moments under side loads; always pair this unit with an external guide rail to prevent premature seal wear.
Quick checklist
The SE40X700SH generates 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum of 128 kgf at 1.0 MPa. It features a PT1/4 port and a 16 mm rod.
Yes, the SE40X700SH is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing mounting hardware. The built-in -S magnet also works seamlessly with AirTAC CMSE reed and DMSE electronic sensors for position feedback.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.