
The AirTAC SE40 Standard Cylinder SE40X700SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 700mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X700SN is a double-acting single-rod ISO 15552 profile cylinder engineered for a 700 mm stroke. At 0.5 MPa it generates 628 N of push force and 528 N of pull force, scaling to 879 N push at 0.7 MPa. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while leaving three dedicated sensor grooves open for position detection.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke confirmation. The NBR seal handles standard operating temperatures from -20 to +70 C. Field-adjustable pneumatic cushioning at both ends allows you to tune end-stop deceleration via a set screw, softening impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X700SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Extends a 700 mm routing flap to push heavy corrugated cartons between sorting lanes, utilizing the 628 N push force to overcome side friction.
Raises heavy fabric warp beams into loom loading position, where the 30 mm adjustable cushion smoothly decelerates the 800 mm/s rapid traverse.
Acts as a hard mechanical stop for sheet metal feeding into a stamping press, using the DMSE sensor to confirm the 700 mm extension before the ram cycles.
Selecting this 40 mm bore makes sense when you need 628 N push at 0.5 MPa but want to avoid the bulk of larger units. If your application requires less force, stepping down to a 32 mm bore yields 402 N push; conversely, scaling up to a 50 mm bore provides 982 N push. Because this is a double-acting cylinder, it relies on continuous air pressure to hold position—if air is lost or the valve centers, the piston will drift, so a BSE rod lock is required for strict holding.
At 700 mm of stroke, the 16 mm rod and front bearing face significant bending moments under side loads; always guide the load externally to prevent premature wear. For direct retrofits, this SE cylinder shares the exact ISO 15552 mounting interface and PT1/4 port of competing standard profile cylinders, allowing you to reuse existing FA flanges or LB foot mounts without redesign.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N push and 528 N pull force. At 0.7 MPa, push increases to 879 N, with a maximum push of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No. The adjustable air cushion at both ends only decelerates the piston near the stroke ends; it is not a locking mechanism. If the air supply is lost, the piston will drift. For fail-safe load holding, consider the BSE rod lock variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.