
The AirTAC SE40 Standard Cylinder SE40X70S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 70mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X70S is a double-acting single-rod ISO 15552 profile cylinder engineered for mid-range pneumatic tasks. It delivers 628 N of push force at 0.5 MPa and operates efficiently between 30-800 mm/s. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke verification. The field-adjustable air cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, softening impacts during high-speed cycling without relying on fixed rubber bumpers.
| Model | Airtac SE40 Standard Cylinder SE40X70S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the 70 mm stroke on horizontal flow wrappers to close end-seal jaws, utilizing the 628 N push force to cleanly crimp packaging film around consumer goods.
Actuates a diverting arm on a distribution conveyor, relying on the DMSE electronic sensor to confirm the 70 mm extend position before routing boxes to secondary lanes.
Shifts a CNC lathe safety enclosure, using the compact tie-rod-free profile barrel to fit neatly within the tight clearances of the machine tool envelope.
When sizing this bore, compare your load requirements against neighboring options: the SE32 bore provides 402 N of push at 0.5 MPa for lighter duties, while the SE50 bore steps up to 982 N for heavier clamping. Because this is a double-acting cylinder, it relies on continuous air pressure to move and hold the piston; if air is lost or the valve centers, the load will drift. For applications requiring true position holding without live pressure, consider the BSE rod-lock variant. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement for other standard profile cylinders, utilizing the same mounting hardware and a PT1/4 port.
Quick checklist
The SE40X70S generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. It features a PT1/4 port and a 16 mm rod.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke end; it is not a mechanical brake. If air is exhausted or pressure drops, the piston will drift. For fail-safe load holding, an external pilot-operated check valve or the AirTAC BSE rod-lock series is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.