
The AirTAC SE40 Standard Cylinder SE40X75SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 75mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X75SFTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact automation. It delivers a 628 N push force at 0.5 MPa (879 N at 0.7 MPa) across a 75 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, flush exterior that resists corrosion and simplifies bracket mounting. Equipped with an FTC center trunnion accessory, it handles pivoting loads with precision.
This unit includes a built-in magnet (-S) for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches, which seat neatly into the sensor grooves on three sides of the body. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, eliminating hard impact when cycling at speeds up to 30-800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X75SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push at 0.5 MPa required to fold corrugated cardboard flaps on high-speed packaging lines without crushing the box structure.
Uses the FTC center trunnion to pivot a sorting gate, leveraging the 75 mm stroke to redirect pallets on a conveyor while accommodating angular movement.
Cycles test probes onto printed circuit boards, utilizing the -S magnet with DMSE electronic sensors to confirm exact engagement position before electrical testing begins.
Selecting this 40 mm bore makes sense when your application requires roughly 628 N of push force at 0.5 MPa. If your payload is lighter, stepping down to the 32 mm bore yields 402 N of push, conserving compressed air. For heavier payloads requiring more thrust, stepping up to the 50 mm bore provides 982 N of push. The PT1/4 port and 16 mm rod handle standard side loads, but because this is a double-acting cylinder, it will drift and cannot hold a vertical load if air pressure is lost—implement an external rod lock or pilot-operated check valve for fail-safe holding. Dimensionally interchangeable per ISO 15552, it serves as a direct replacement for other ISO 15552 cylinders, matching the 40 mm bore, 75 mm stroke, PT1/4 port, and FTC mounting footprint exactly.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder outputs 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE40X75SFTC is dimensionally interchangeable per ISO 15552. You can use it as a direct replacement for other ISO 15552 profile cylinders with a 40 mm bore, 75 mm stroke, and FTC mounting interface, provided your port matches the standard PT1/4 thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.