
The AirTAC SE40 Standard Cylinder SE40X75SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 75mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X75SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding environments. It generates 628 N of push force at 0.5 MPa and features a 40 mm bore paired with a 75 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.
This specific configuration includes a built-in magnet (S) for seamless positioning feedback via CMSE reed or DMSE electronic sensors, and a Viton (FKM) H-seal rated for continuous operation up to 150 C. Field-adjustable pneumatic cushioning at both stroke ends allows precise deceleration tuning to dampen hard mechanical impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X75SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the heat-sealing head on continuous thermoform packaging lines, where the 628 N push force secures seams and the FKM seal withstands 150 C ambient radiated heat.
Powers a 75 mm stroke routing flap on high-speed sortation conveyors, utilizing the built-in magnet and DMSE sensors to confirm gate position before product arrival.
Indexes aluminum extrusions into machining centers using the compact tie-rod-free profile, keeping the staging fixture low-profile and free from external snag points.
Generating 628 N of thrust at 0.5 MPa, this 40 mm bore is a mid-range actuator. If your assembly requires less force, the 32 mm variant outputs 402 N; for heavier payloads, stepping up to the 50 mm bore yields 982 N. Because the SE is a double-acting cylinder, it cannot hold a load if air pressure drops or the valve centers—the piston will drift. For position-holding safety, consider the BSE rod-lock series. The 75 mm stroke is well below the side-load threshold, but the 16 mm rod and M12x1.25 thread handle standard lateral stresses effectively.
As a true ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other ISO 15552 actuators. You can reuse existing mounting hardware and PT1/4 pneumatic ports. The integrated -S magnet enables direct installation of CMSE or DMSE sensors without extra machining.
Quick checklist
This cylinder provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. Equipped with a Viton (FKM) seal, it operates reliably from -20 C up to 150 C.
No. The adjustable air cushion at both ends only decelerates the piston near the end of its stroke; it is not a mechanical brake. If air is lost, the piston will drift. For holding vertical loads without live pressure, use an AirTAC BSE rod-lock cylinder or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.