
The AirTAC SE40 Standard Cylinder SE40X75SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 75mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X75SN is a double-acting, single-rod ISO 15552 profile cylinder featuring a 40mm bore and 75mm stroke. It delivers a robust 628 N push force at 0.5 MPa, making it well-suited for mid-range industrial actuation. The extruded aluminum barrel design omits external tie rods, yielding a smooth, compact body that resists corrosion and mounts flush in tight machine envelopes.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing along three integrated sensor grooves. The NBR seal handles standard operating temperatures from -20 to +70 C, while the field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration for faster cycle speeds without mechanical impact.
| Model | Airtac SE40 Standard Cylinder SE40X75SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 628 N push and 75mm travel needed to fold and seal corrugated carton flaps on high-speed packaging lines.
Actuates routing gates on modular conveyor networks, using the built-in S magnet to trigger DMSE electronic sensors for package sorting.
Drives the safety interlock door on a CNC turning center, benefiting from the smooth tie-rod-free profile that prevents chip accumulation.
This 40mm bore provides 628 N of push force at 0.5 MPa. If your application requires less force, stepping down to a 32mm bore yields 402 N, while moving up to a 50mm bore provides 982 N. The standardized ISO 15552 mounting interface ensures this cylinder is a direct dimensional replacement for other ISO 15552 profile cylinders, sharing standard mounting accessories like FA front flanges or LB foot brackets. The PT1/4 port and M12x1.25 rod thread are set by the 40mm bore standard.
Because this is a double-acting cylinder, it does not hold a load if air pressure is lost or the valve centers; the piston will drift. For position-holding safety, consider a BSE rod lock variant. With a 75mm stroke, side-load bending is minimal, but always verify the rod-end thread alignment to prevent premature seal wear.
Quick checklist
At 0.5 MPa, the 40mm bore provides 628 N of push force and 528 N of pull force. At 0.7 MPa, push force reaches 879 N, with a maximum push of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE40X75SN is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing mounts and use the integrated magnet with AirTAC CMSE or DMSE sensors, but note the NBR seal is optimized for standard temperatures rather than high heat.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.