
The AirTAC SE40 Standard Cylinder SE40X780S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 780mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X780S is a double-acting single-rod profile cylinder engineered to the ISO 15552 / VDMA 24562 standard. It delivers 628 N of push force at 0.5 MPa and 528 N of pull force, making it a solid choice for mid-range automation tasks. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This 40 mm bore unit features a 780 mm stroke and includes a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic sensors. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration, protecting tooling from hard impacts during high-speed cycling.
| Model | Airtac SE40 Standard Cylinder SE40X780S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 780 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×780 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Ideal for pushing corrugated cartons across 780 mm wide sorting belts, using the 628 N push force to overcome box friction without stalling.
Provides the long 780 mm extension needed to position packaging film rolls, while the -S magnet triggers DMSE sensors to stop the unwind cycle.
Deploys the 780 mm stroke to open laboratory test chamber doors, utilizing the adjustable cushion to prevent slamming heavy shielded panels.
If you need slightly less force, the adjacent 32 mm bore provides 402 N of push at 0.5 MPa. Stepping up to the 50 mm bore increases that output to 982 N. The SE40X780S uses a PT1/4 port and M12x1.25 rod thread, but because this is a 780 mm stroke, the extended rod is highly susceptible to bending under side loads—always support the load with an external guide. As a standard ISO 15552 profile cylinder, it serves as a direct replacement for other ISO 15552 cylinders without requiring new mounting hardware. Note that this cylinder does not hold position when air is exhausted; a BSE rod lock is required for fail-safe holding.
Quick checklist
At 0.5 MPa, the SE40X780S generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force reaches 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
No, the SE40X780S is a standard double-acting cylinder and will drift if air is lost. The adjustable air cushion only decelerates the piston near the stroke ends and does not act as a brake. For fail-safe position holding, use a BSE series rod lock cylinder or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.