
The AirTAC SE40 Standard Cylinder SE40X800S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 800mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X800S is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding pneumatics. It delivers 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa, utilizing a 16 mm hard-chrome rod with an M12x1.25 thread. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.
Equipped with a built-in magnet (-S), this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts during high-speed 800 mm travel before the 30 mm cushion length absorbs residual energy.
| Model | Airtac SE40 Standard Cylinder SE40X800S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles high-speed lane routing of filled containers over an 800 mm span, relying on 628 N push force to actuate heavy guide arms without lag.
Extends the full stroke to dispense slip sheets between pallet layers, using the built-in magnet to confirm sheet placement for the packaging controller.
Drives horizontal retrieval arms in dense ASRS aisles, where the flush tie-rod-less profile prevents debris accumulation along the long travel path.
Stepping down to a 32 mm bore reduces the 0.5 MPa push to 402 N, whereas stepping up to a 50 mm bore increases it to 982 N, providing a clear upgrade path if your payload grows. Because this is a double-acting cylinder, it cannot hold a load unpowered—air loss causes drift, requiring an external pilot-operated check valve for static positioning. At 800 mm of travel, the 16 mm rod is highly susceptible to side-load bending; pair it with an external linear guide to prevent premature bearing wear. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement sharing standard mounting hardware and PT1/4 ports.
Quick checklist
At 0.5 MPa, it provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa operating pressure.
Yes, the SE40X800S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounting hardware using the PT1/4 port and standard accessories, though you must retain the external guide for this 800 mm stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.