
The AirTAC SE40 Standard Cylinder SE40X800SFA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 800mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X800SFA is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a push force of 628 N at 0.5 MPa and a maximum push capacity of 128 kgf at 1.0 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The built-in magnet enables seamless position detection using AirTAC CMSE reed or DMSE electronic sensors.
Equipped with a front flange (FA) mount and a generous 800 mm stroke, this 40 mm bore unit relies on field-adjustable pneumatic cushioning at both ends to decelerate the piston smoothly before end-of-travel impact. The cushion screws can be tuned on-site to match the actual moving load and speed, preventing harsh mechanical shocks without relying on fixed rubber bumpers.
| Model | Airtac SE40 Standard Cylinder SE40X800SFA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Extends an 800 mm routing arm on a packaging conveyor, using the 628 N push force at 0.5 MPa to pivot heavy cardboard cartons into secondary processing lanes.
Transfers stacked goods across a wide roller bed, leveraging the full 800 mm stroke and front flange mount to maintain rigid alignment during extended horizontal travel.
Sweeps pressed sheet metal panels into alignment fixtures, relying on the DMSE electronic sensor to verify the 40 mm rod has fully retracted before the press cycles.
This 40 mm bore cylinder provides 628 N of push force at 0.5 MPa. If your application requires less power, stepping down to the 32 mm bore yields 402 N of push force; conversely, scaling up to the 50 mm bore provides 982 N. The FA front flange provides a rigid face-mount for straightforward perpendicular loading, and the PT1/4 port ensures standard pneumatic connectivity.
Because this unit features an 800 mm stroke, the 16 mm rod and internal bearing face increased bending moments under side loads—always incorporate an external guide rail to support the payload and prevent premature seal wear. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure is lost, so a BSE rod lock is required for fail-safe positioning.
Quick checklist
This 40 mm bore cylinder features a PT1/4 port and generates 628 N of push force and 528 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 879 N, and it reaches a maximum push capacity of 128 kgf at 1.0 MPa.
Yes, its ISO 15552 dimensional footprint allows it to direct replace comparable profile cylinders using existing FA front flange mounting hardware. However, the adjustable air cushion only decelerates the piston at stroke ends; it cannot hold a load mid-stroke or prevent drift upon loss of air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.