
The AirTAC SE40 Standard Cylinder SE40X80FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 80mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X80FTC is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a push force of 628 N at 0.5 MPa and a maximum push capacity of 128 kgf. Its extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This 40 mm bore unit features an FTC mounting interface and a PT1/4 port. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration for a 30 mm cushion length. Note that this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE position sensing without modification.
| Model | Airtac SE40 Standard Cylinder SE40X80FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the mechanical arms that fold corrugated carton flaps prior to tape sealing, utilizing the 80 mm stroke and 628 N push force to cleanly crease heavy cardboard without stalling.
Actuates routing gates on beverage filling lines to separate continuous product flow into distinct lanes, relying on the FTC mount to handle repeated lateral shifting.
Lowers electronic test probes onto printed circuit boards, where the compact tie-rod-free profile allows dense mounting of multiple cylinders in a small fixture space.
Choosing this 40 mm bore makes sense when you need 628 N of push force at 0.5 MPa. If your load is lighter, stepping down to the 32 mm bore drops the push force to 402 N, whereas stepping up to the 50 mm bore increases it to 982 N. Because this is a standard 80 mm stroke, side-load stress on the M12x1.25 rod thread is minimal.
This SE40X80FTC variant uses an FTC mount and is dimensionally interchangeable with other ISO 15552 cylinders for straightforward retrofits. Remember that the adjustable air cushion only softens the piston stop; it does not lock the rod. If your process loses air pressure, the cylinder will drift, so you must add a BSE rod lock or external pilot check valve for position holding.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE40X80FTC is dimensionally interchangeable per ISO 15552 standards. You can swap it directly into existing machinery using the same mounting hardware and port spacing. Just ensure your setup accommodates the PT1/4 port thread and the FTC mounting accessory.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.