
The AirTAC SE40 Standard Cylinder SE40X80SCA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 80mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X80SCA is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It delivers 628 N of push force at 0.5 MPa and 528 N of pull force, utilizing a 16 mm hard-chrome plated rod. Engineered with a square extruded aluminum barrel, this unit omits external tie rods to present a completely flush, corrosion-resistant exterior that simplifies mounting clearance.
This specific configuration includes a built-in magnet for CMSE and DMSE position sensing, paired with a CA single clevis mounting accessory for articulated pivot joints. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s operations.
| Model | Airtac SE40 Standard Cylinder SE40X80SCA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the rotary and reciprocating sealing jaws on continuous motion flow wrappers, using its 628 N thrust and 80 mm stroke to cleanly crimp and sever packaging film.
Pivots a sorting flap on a package handling conveyor via the CA clevis mount, rapidly redirecting cartons into specific routing lanes at speeds up to 800 mm/s.
Controls the tensioning levers on weaving machinery, where the adjustable end cushions absorb kinetic energy to protect delicate yarn guides during retraction.
If your assembly requires slightly less thrust, the adjacent SE32 bore provides 402 N of push at 0.5 MPa; conversely, scaling up to the SE50 bore yields 982 N for heavier payloads. The CA clevis mount is ideal for pivoting mechanisms, but remember that a plain SE cylinder will drift and cannot hold a load if air pressure is lost or the valve is centered—use a BSE rod lock variant if position holding is mandatory. For this 80 mm stroke, side-load on the rod bearing is minimal, but always verify radial loads are guided externally.
Quick checklist
The SE40X80SCA delivers 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum of 128 kgf at 1.0 MPa. It features a PT1/4 port and a 16 mm diameter rod with an M12x1.25 thread.
Yes, the SE series is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other standard profile cylinders. The integrated -S magnet also allows direct fitting of AirTAC CMSE reed or DMSE electronic sensors without extra machining.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.