verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X820S

The AirTAC SE40 Standard Cylinder SE40X820S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 820mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke820 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$143.27 $150.77Save 4% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X820S

The AirTAC SE40X820S is a double-acting single-rod ISO 15552 profile cylinder, engineered to deliver 628 N of push force and 528 N of pull force at 0.5 MPa. Because this 820 mm stroke exceeds the standard 1200 mm maximum for a 40 mm bore, it is supplied as a non-standard made-to-order unit. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while leaving the integrated sensor grooves fully accessible on three sides.

This specific model includes a built-in magnet (-S) for seamless positioning feedback using AirTAC CMSE reed or DMSE electronic sensors. To protect the piston at high cycling speeds, the cylinder features field-adjustable air cushioning at both ends. By turning a setscrew, technicians can fine-tune the end-of-stroke deceleration to eliminate hard mechanical impacts without relying on fixed rubber bumpers.

Airtac SE40 Standard Cylinder SE40X820S Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X820S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke820 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X820S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×820Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X820S Is Used

conveyor_belt

Pallet Stretch Wrapper

Drives the film carriage up and down an 820 mm mast on a packaging line, using the 628 N push force to elevate the wrapping assembly smoothly.

science

Lab Sample Dispenser

Actuates a long-travel sampling probe across multiple test tubes, relying on the -S magnet and DMSE sensors for precise carriage positioning.

warehouse

Vertical Storage Elevator

Raises and lowers tote diverts in an automated retrieval system where the compact tie-rod-free extruded barrel saves critical overhead clearance.

Is the Airtac SE40 Standard Cylinder SE40X820S the Right Cylinder?

Selecting the SE40X820S makes sense when your mechanism requires a very long reach but only moderate force. If you need less thrust, stepping down to the 32 mm bore drops the 0.5 MPa push force to 402 N. If your load demands more power, stepping up to the 50 mm bore increases the 0.5 MPa push force to 982 N. Keep in mind that a plain SE cylinder will drift and cannot hold a load if air pressure is lost or the valve is centered; use a BSE rod lock for secure positioning. Furthermore, spanning 820 mm creates a significant bending moment on the 16 mm rod and front bearing. To prevent premature seal wear and binding, always guide the load externally rather than letting the rod support cantilevered weight. As a true ISO 15552 profile cylinder, it offers a direct dimensional replacement for other ISO 15552 cylinders using the same PT1/4 port and mounting interface.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X820S FAQ

At 0.5 MPa, the SE40X820S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.

Yes. The SE40X820S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, PT1/4 port size, and 40 mm bore interface. You can drop it directly into existing machinery designed for ISO 15552 profile cylinders.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X820S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X820S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.