
The AirTAC SE40 Standard Cylinder SE40X840S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 840mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X840S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a non-standard 840mm stroke. It generates 628 N of push force and 528 N of pull force at 0.5 MPa, making it well-suited for long-travel actuation in mid-range automation. The extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along three integrated grooves.
This specific unit includes a built-in magnet (-S) for non-contact position detection, interfacing directly with AirTAC CMSE reed and DMSE electronic switches. Because the stroke exceeds the standard 800mm maximum for this bore, it is manufactured as a made-to-order unit. Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening mechanical impacts during high-speed traversals.
| Model | Airtac SE40 Standard Cylinder SE40X840S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 840 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×840 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a 840mm stroke to index empty pallets onto an assembly conveyor, utilizing the 628 N push force to overcome cart rolling friction without requiring a larger bore.
Extracts automated testing racks from a shielded enclosure, relying on the -S magnet and DMSE electronic sensors to confirm full extension before the door opens.
Unwinds large packaging film rolls across the long stroke, using the field-adjustable air cushions to gently decelerate the heavy mass at the end of each traverse.
When sizing this 40mm bore, evaluate your actual thrust requirements: stepping down to a 32mm bore reduces the 0.5 MPa push to 402 N, while stepping up to a 50mm bore increases it to 982 N. Because this 840mm stroke is non-standard and exceeds the catalog maximum, expect extended lead times and verify that your pneumatic infrastructure can sustain the PT1/4 port flow across the full travel distance.
With an 840mm stroke, the unsupported mass of the Ø16mm piston rod introduces a high risk of rod-bearing bending and premature wear under side loads. An external linear guide is strongly recommended to prevent binding and seal failure. Furthermore, if the application requires the load to be held in place during an air loss event, this cylinder will drift; an external pilot-operated check valve or a BSE rod-lock variant is necessary for true static holding. For retrofitting, its ISO 15552 mounting interface ensures dimensional interchangeability with other standard profile cylinders.
Quick checklist
At 0.5 MPa, this 40mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force is 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE40X840S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards, meaning it shares the exact same mounting footprint and interface as other standard profile cylinders. You can drop it into existing ISO 15552 mounting hardware without modifications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.