
The AirTAC SE40 Standard Cylinder SE40X900STC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 900mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X900STC is a double-acting, single-rod ISO 15552 profile cylinder engineered for precise linear motion across a 900 mm stroke. It delivers a robust 628 N push force at 0.5 MPa, utilizing a 16 mm hard-chrome piston rod and a PT1/4 port. Designed with a square extruded aluminum barrel, the body omits external tie rods to provide a flush, corrosion-resistant exterior that simplifies bracket mounting.
This configuration includes a built-in magnet for CMSE or DMSE position sensing, paired with a TC centre trunnion mounting accessory. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X900STC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 900 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×900 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 900 mm stroke and 628 N push at 0.5 MPa to index empty pallets laterally between roller conveyor lanes without requiring a multi-stage cylinder.
Leverages the TC trunnion mount to accommodate the slight arc of a pivoting ejection arm, safely pushing heavy packaging film rolls out of a wrapping station.
Deploys the 879 N push at 0.7 MPa to deflect plastic totes onto a secondary accumulation line, relying on the -S magnet to confirm full diversion.
Selecting this 40 mm bore makes sense when an application requires 628 N of push at 0.5 MPa but cannot justify the 982 N output of the next size up, the 50 mm bore. Conversely, if your load demands less force, stepping down to the 32 mm bore yields 402 N. Because the 900 mm stroke creates a long lever arm, side loads will induce significant bending moments on the rod bearing; an external guide rail is strongly recommended to prevent premature seal wear.
This model is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders. It features a PT1/4 port, TC centre trunnion mounting, and a built-in magnet for CMSE or DMSE sensors. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not lock the rod, so a BSE rod lock is required if the load must be held without live air pressure.
Quick checklist
This 40 mm bore cylinder provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. Its operating speed ranges from 30 to 800 mm/s.
Yes, the SE40X900STC shares the standardized ISO 15552 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can retain existing TC trunnion brackets and mounting hardware during a retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.