
The AirTAC SE40 Standard Cylinder SE40X90SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 90mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X90SH is a double-acting single-rod ISO 15552 profile cylinder engineered for rigorous actuation. It generates 628 N of push force at 0.5 MPa, utilizing a 16 mm rod and a PT1/4 port for balanced pneumatic flow. The 90 mm stroke provides precise linear movement within a compact footprint.
Designed with a square extruded aluminum barrel that eliminates external tie rods, this unit mounts flush against machine frames to resist corrosion and save space. Equipped with an FKM seal, it withstands operating temperatures up to 150 C, while the built-in magnet enables seamless integration with CMSE reed and DMSE electronic sensors for position tracking.
| Model | Airtac SE40 Standard Cylinder SE40X90SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folder arms on continuous film packaging lines, relying on the 90 mm stroke and FKM seal to withstand ambient heat from shrink tunnels.
Pushes decorated parts out of heated fixtures, utilizing the 628 N extend force at 0.5 MPa and the high-temp Viton elastomer to resist thermal degradation.
Pivots sorting gates on logistics conveyors, using the integrated magnet to trigger DMSE electronic sensors for precise mid-stroke routing confirmation.
When sizing this 40 mm bore actuator, evaluate your force margins against adjacent options. Stepping down to a 32 mm bore drops the 0.5 MPa push force to 402 N, whereas moving up to a 50 mm bore increases it to 982 N, giving you room to scale if the 628 N output is borderline. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders, utilizing the same mounting hardware and PT1/4 ports.
Remember that the adjustable air cushion at both ends only decelerates the piston near stroke end to soften hard impacts; it is not a locking mechanism. If your process loses air pressure, the rod will drift, so an external pilot-operated check valve or a BSE rod lock variant is required to hold a suspended load safely.
Quick checklist
At 0.5 MPa, this 40 mm bore cylinder provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force reaches 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range spans 30-800 mm/s.
Yes, the SE40X90SH is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface and hole patterns as other standard profile cylinders. You can swap it in as a direct replacement using your existing mounting brackets and PT1/4 pneumatic fittings.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.