
The AirTAC SE40 Standard Cylinder SE40X950 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 950mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X950 is a double-acting single-rod ISO 15552 profile cylinder engineered for a 950mm stroke, yielding a theoretical push force of 628N at 0.5MPa and 879N at 0.7MPa. Because 950mm exceeds the standard maximum stroke for a 40mm bore, this unit is configured as a made-to-order extension to suit long-travel automation. The extruded aluminum barrel omits external tie rods, yielding a smooth corrosion-resistant exterior that mounts flush against machine frames.
This model features field-adjustable pneumatic cushioning at both ends to decelerate the piston near stroke limits, though it lacks the -S magnet option for CMSE or DMSE position sensing. The standardized ISO 15552 interface ensures strict dimensional interchangeability with other cylinders in this footprint class.
| Model | Airtac SE40 Standard Cylinder SE40X950 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 950 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×950 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 950mm stroke to push heavy cardboard cartons between parallel conveyor lanes, utilizing the 628N push force at 0.5MPa to overcome box friction.
Advances sheet metal blanks into a press brake, where the smooth extruded profile prevents material scratching and the adjustable cushion decelerates the long travel safely.
Drives a horizontal retrieval arm in a vertical lift module, relying on the ISO 15552 mounting interface for precise direct alignment and 879N push at 0.7MPa.
At 0.5MPa this 40mm bore generates 628N of push force. If your assembly requires less thrust, stepping down to the 32mm bore yields 402N push, while stepping up to the 50mm bore provides 982N push. As a non-standard 950mm stroke, this cylinder is made-to-order. Because the stroke exceeds 300mm, the 16mm rod and thread face increased bending moments under side loads; an external guide bearing is strongly recommended to prevent rod-bearing wear. Note that a plain SE cylinder will drift if air pressure is lost—the adjustable cushion only softens end-of-stroke impacts and does not lock the load. For direct retrofits, match the 40mm bore, 950mm stroke, PT1/4 port, and your required mounting accessory.
Quick checklist
The 40mm bore provides a push force of 628N at 0.5MPa and 879N at 0.7MPa, with a pull force of 528N at 0.5MPa. The maximum push force is 128kgf at 1.0MPa. The operational speed range is 30-800mm/s.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders and shares standard mounting hardware. However, it does not hold position if air is lost; the adjustable air cushion only decelerates the piston near stroke end rather than locking the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.