
The AirTAC SE40 Standard Cylinder SE40X950S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 950mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X950S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 950 mm stroke. Because this length exceeds the standard 1200 mm catalogue maximum for a 40 mm bore, it is produced as a made-to-order unit to support extended travel requirements. It delivers 628 N of push force and 528 N of pull force at 0.5 MPa, utilizing a 16 mm hard-chrome plated rod.
The extruded aluminum barrel eliminates external tie rods, resulting in a compact, corrosion-resistant body that mounts flush within tight machine frames. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speed. The integrated -S magnet enables direct mounting of AirTAC CMSE reed and DMSE electronic sensors along the three dedicated sensor grooves.
| Model | Airtac SE40 Standard Cylinder SE40X950S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 950 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×950 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy corrugated cartons across a 950 mm transfer belt, utilizing the 628 N push force to overcome friction without stalling.
Extends the full 950 mm stroke to feed large MDF sheets into an edge-banding machine, where the adjustable cushion prevents harsh end-stop bouncing.
Raises and lowers dyeing racks in a humid environment, leveraging the corrosion-resistant extruded aluminum profile and CMSE/DMSE sensor magnet tracking.
For applications requiring less force, stepping down to a 32 mm bore yields 402 N of push at 0.5 MPa, while stepping up to a 50 mm bore provides 982 N if your load demands more thrust. Because this 950 mm stroke is non-standard, expect a made-to-order lead time. At 950 mm of unsupported travel, the 16 mm rod is highly susceptible to side-load bending; an external linear guide is strongly recommended to prevent premature rod-bearing wear. Remember that this cylinder relies on live air pressure to hold position—if air is lost, the piston drifts, so specify a BSE rod lock for fail-safe holding. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement sharing standard mounting accessories and PT1/4 ports.
Quick checklist
At 0.5 MPa, the SE40X950S provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with a maximum push capacity of 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE40X950S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, PT1/4 port size, and M12x1.25 rod thread as competing ISO profile cylinders for seamless retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.