verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE40 Standard Cylinder SE40X950SN

The AirTAC SE40 Standard Cylinder SE40X950SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 950mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ40 mm
  • Stroke950 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM12×1.25
  • CushionAdjustable, 30 mm
$154.43 $161.93Save 4% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE40 stroke, mounting and version on one page All SE40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE40 Standard Cylinder SE40X950SN

The AirTAC SE40X950SN is a double-acting single-rod ISO 15552 profile cylinder engineered for a 950 mm stroke. It generates 628 N of push force at 0.5 MPa and incorporates an NBR seal compound suitable for standard operating temperatures. Because this 950 mm length exceeds the standard maximum stroke for the 40 mm bore, it is produced as a made-to-order unit.

The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. Sensor grooves on three body sides accept AirTAC CMSE reed and DMSE electronic switches, leveraging the built-in -S magnet for precise end-position detection. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration for the moving load.

Airtac SE40 Standard Cylinder SE40X950SN Technical Specifications

ModelAirtac SE40 Standard Cylinder SE40X950SN
SeriesSE ISO 15552 profile cylinder
Bore sizeØ40 mm
Stroke950 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM12×1.25
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE40 Standard Cylinder SE40X950SN

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
40Bore size in mm.
×950Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE40 Standard Cylinder SE40X950SN Is Used

conveyor_belt

Transfer Gate Diverter

Actuates a diverter arm over a 950 mm span to route packages between sorting lanes, utilizing the 628 N push force to overcome carton friction.

straighten

Long-Stroke Press Ejector

Pushes stamped metal sheets out of a hydraulic press bed, where the extended stroke clears deep tooling and the NBR seal withstands shop-floor lubricants.

warehouse

Vertical Storage Tray Lift

Raises and lowers heavy storage trays in automated retrieval systems, relying on the built-in magnet and DMSE sensors to confirm vertical travel endpoints.

Is the Airtac SE40 Standard Cylinder SE40X950SN the Right Cylinder?

When sizing this actuator, you can step down to the 32 mm bore for a lighter 402 N push at 0.5 MPa, or move up to the 50 mm bore for a stronger 982 N thrust. Because the 950 mm stroke is non-standard, expect a made-to-order lead time. This unit uses a PT1/4 port and a 16 mm rod with an M12x1.25 thread.

At 950 mm, the unsupported piston rod is highly susceptible to bending under side loads; always use an external guide to prevent rod-bearing damage. Note that a standard SE cylinder will drift if air pressure is lost or the valve centers—use a BSE rod lock for position-holding requirements. As a true ISO 15552 profile cylinder, it offers direct dimensional interchangeability with other ISO 15552 cylinders, sharing standard mounting hardware.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE40 Standard Cylinder SE40X950SN FAQ

This 40 mm bore cylinder provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It operates on filtered air at 0.15-1.0 MPa, runs at speeds of 30-800 mm/s, and features a PT1/4 port.

No, the standard SE cylinder cannot hold a load without live air pressure; the piston will drift if air is lost or the valve is centered. The adjustable air cushion only decelerates the piston near the stroke ends and does not function as a mechanical brake. For fail-safe load holding, use an AirTAC BSE series rod lock.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE40 Standard Cylinder SE40X950SN

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE40X950SN and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.